大家在查：吴晓玲还原回去 thundercap NiagaraFall MPB 基诺比利 for finding MustaphaKamelal-Sayed 1030亿马立斯

冲头

na.【自】head; formed punch
网络plunger chip; Punches; ram

冲头

英-汉网络释义

冲头

punch

机械英语词汇|各类常用英语词汇 ... lower stripper 下脱料板零件类 punch 冲头 deburring punch 压毛边冲子 ...

plunger chip

chip是什么意思?_百度知道 ... planar chip 平面片 plunger chip 冲头 polymer chips 聚合物切片 ...

Punches

模具英语例句 - 漫步者的日志 - 网易博客 ... Pilots 引导冲 M-2 Punches 冲头 M-2 a. Grind shear. 修模刀口 ...

ram

航海及海运专业英语词汇(R1) ... ram wing 冲翼 ram 冲头 ram 水下冰角 ...

punch pin

希高翻译-国际贸易相关术语中英对照四十一 ... punch on 凿孔开始 punch pin 冲头 punch test 冲压试验 ...

drift

drift的翻译中文意思-在线英汉词典 ... n.漂流,漂流物,堆积物 drift n.冲头,滑移,偏移 drift n.偏航,漂流,漂移 drift ...

punch head

1 2 3 4 5 ... 穿孔卡抄录器^ punch card transcriber 冲头^ punch head 冲孔机^ punch machine ...

plunger tip

机械部件的词汇，共享 _ 上海疯狂英语 ... plunger tester 压力强度测定仪 plunger tip 冲头 plunger type 柱塞式 ...

例句：

Do not strike punch in such a manner as to exert force straight down onto the bearing inner ring .

不得这样笔直地击打冲头，防止外力直接传到轴承内圈上。

The grooving die set is composed of a punch edge and a groove edge which have the same shape .

开槽模具由具有形状相同的冲头刃、槽刃组成。

All sections , punches , and buttons that are similar in appearance are to have mistake proofing techniques used.

所有模具零件，冲头，模板在外观上相似的地方需要用技术的方法来证实没有用错材料

Heel blocks should have screws located on the side of the block toward the thrust .

跟刀靠向冲头一侧应该有螺丝定位。

The aim of the utility model is to design a special-shaped pipe expanding plunger chip with high pipe expanding efficiency and good quality .

本实用新型的目的是设计一种扩管效率高且质量好的异型扩管冲头。

The utility model discloses a special-shaped pipe expanding plunger chip and relates to a special-shaped pipe shaping tool .

本实用新型公开了一种异型扩管冲头，涉及一种异型管成型工具。

The quality of the internal surface can be greatly improved and the punch force can be significantly reduced by using inner set hose .

内置软管可以有效改善管材的内表面质量，并显著减小冲头推力。

A die punch can be used as the electrode to reproduce its shape in the matching die plate , complete with the necessary clearance .

可用冲头作电极，在阴模板上复制其形状，并留有必须的间隙。

Defect on the cage caused by punches , which do not move freely on the center pin; cause a deformed bottom or side of cage .

由于冲头不能在中心销上自由地运动，造成保持架底部或者边侧的变形缺陷。

Pierce and trim punch heights must be staggered , where design permits, to minimize press shock and noise.

刺破和修剪得冲头高度需要错开，以便产生最小的压力和噪音

and the diameter of the spline punch is smaller than the cavity diameter at the lower part of the T-shaped structure workpiece cavity .

所述的花键冲头的直径小于 T 形结构工件腔的下部腔径。

Ballast using ductile iron punch shot , the normal service life of only about 2 thousand times , need frequent replacement of punch.

压射冲头采用球墨铸铁，正常使用寿命只有 2千次左右，需频繁更换冲头。

Manifolds will be mounted with the screws going through the manifold into the punch or die shoes.

将分流式系统用螺丝所在冲头或模座上。

Controls must be recessed inside the punch or die shoe and facing the operator .

控制开关必须凹入面对操作者一侧的冲头或模座内。

b. Wire E. D. M. "stick" punches having their shape burned through the retainer, are recommended.

对线割的冲头，推荐在其固定器上线割出其形状。

PRESS TOOLS . RECTANGULAR RETAINERS AND PERCUSSION PLATE FOR FLANGED PUNCHES . TOP FIXING.

冲压工具 .带凸缘冲头矩形固定板和挡板

The punch pushes against the workpiece, which is held in the die . Punch presses are usually driven by electric motors .

冲头推压装于模具中的工件。冲床通常由电动机驱动。

The utility model discloses a plunger chip and relates to the shaping technique without cutting scrap.

本实用新型公开了一种冲头，涉及一种无切屑成形技术。

PRESS TOOLS . SQUARE RETAINERS AND PERCUSSION PLATES FOR FLANGED PUNCHES . TOP FIXING.

冲压工具 .带凸缘冲头正方形固定板和挡板

Blanking and piercing punches must contain slug ejector pins wherever possible.

下料和刺破的冲头需有备件随时更换

Blank and trim entry will occur before piercing punches by one-half stock thickness.

下料及剪边冲应比冲孔冲头高。

Tools for pressing - Punches with cylindrical head and straight or reduced shank .

冲压工具 .有圆柱头和直杆或者缩径柄的冲头

d. Cross-sectional views (for timing, punch length , and travel of springs ).

横断面视图（剪边，冲头长度以及弹簧的行程）

the punch moved down continuously to the upper surface of the base , so as to position the electrode cloth.

冲头继续垂直下移到底座的上表面，实现对电极布的定位；

热词推荐

大家在看

man , . cum you 's " after ? japan : - Facebook what Yeah your then 4th as join