大家在查： gullies Whistler BPM creel 符咒镇住 Backlit 福安之陪葬王羲之话梅

延伸率

n.elongation
网络Elongation; percentage elongation; percentage of elongation

延伸率

英-汉网络释义

延伸率

Elongation

专业英语-注塑成型专业词汇_百度文库 ... gravity 比重 Elongation 延伸率 density 密度 ...

percentage elongation

FLOWEXPO CHINA ... 屈服点 yield point 延伸率 percentage elongation 抗压强度 compressive strength ...

percentage of elongation

矿业工程专业词汇P_百度文库 ... per ton cost 每吨成本 percentage of elongation 延伸率 perched water table 栖留地下水位 ...

Tensile Elongation

模具种类_百度文库 ... tensile strength 抗拉强度 tensile elongation 延伸率 flexural modulus 弯曲模数 ...

specific elongation

冶金专业英语词汇(S) ... specific density 密度 specific elongation 延伸率 specific gravity 比重 ...

elongation rate

电子类常用专业术语（二）_依卡露 - 阿里巴巴博客 ... elongation, 伸长率 elongation rate, 延伸率 elution, 洗脱 ...

elongation percentage

机械词汇的英语翻译(A-G) ... elongation 伸长 elongation percentage 延伸率 elution 洗提 ...

Elongation ratio

无纺布制空气过滤布家用空调首选... ... 撕裂强度 Peel strength 延伸率 Elongation ratio 透气度 Permeability ...

例句：

Tensile strength and elongation of the molybdenum plate were significantly enhanced by the existence of La2O3.

La2O3 的存在显著提高了钼板的抗拉强度和延伸率。

This means that the design will usually have only published values of yield strength , ultimate strength , and percentage elongation .

这就是说，设计人员通常只能利用那些公开发表的屈服强度、极限强度和延伸率等数据资料。

The ultimate tensile strength and elongation of extrusion bar after forging process was much higher than that of the direct extrusion bar .

先锻后挤工艺棒材最终抗拉强度和断后延伸率高于直接挤压棒材。

The ferrite grain size of samples influenced the strength and elongation of dual-phase steels with different martensite contents.

试样的铁素体晶粒大小在不同的马氏体范围内对强度和延伸率有不同的影响。

The elongation rates of the specimens in marine mud with SRB under different potentials are lower than those in marine mud without SRB.

不同电位下，SRB 存在时试样的断裂延伸率均低于海泥中不含 SRB 时的断裂延伸率。

The objective and significance of cold skin pass rolling were simply introduced ; the definition and measuring method were explained .

简单介绍了冷轧平整的目的和意义，说明了延伸率的定义和测量方法。

The results showed that the strength of laser welded joints was increased and the elongation rate was decreased compared with base metal.

结果表明：与母材相比激光焊接头的强度升高，延伸率下降；

This article describes the procedure calculation of the little curved radius tubular semifinished product such as ductility, intensity, etc.

此文阐述了对小弯曲半径管坯弯曲首先应进行工艺计算，如延伸率、强度计算等。

The effect of hydrogen of the gear shaft was comparatively evaluated by reduction in area and elongation values in different condition .

用不同条件测得的断面收缩率和延伸率评价了齿轮轴的氢脆效应；

The research will change the phenomenon that yield stress and elongation are only decided on the basis of experimental result.

该研究改变了材料的屈服应力和延伸率只能凭实验确定的局面。

With elongation increase , high stress concentrations tend to occur at grain boundaries .

随着延伸率增大，晶界易成为应力集中区。

As a result, the tensile or yield strength and elongation of the extrusion decreases with the extrusion speed 's increasing .

随着挤压速度的降低，抗拉强度、屈服强度和延伸率都有一定的提高。

The steel of the reinforcing cords comprises high elongation steel .

构成增强帘线的钢包括高延伸率钢。

With the increase of needle depth, breaking elongation rate decreased.

的增加，产品的断裂延伸率减小；

In order to be deformed , the sections must be made with resins of high elongation at break .

为了防止变形，截面必须使用具有断裂延伸率较高的树脂制成。

Both flange and web exhibited satisfactory elongation characteristics (i. e. 28%).

翼缘和腹板都有令人满意的延伸率（即 28%）。

At the same time copper elongation , crystallization structure would amount to an Etchant characteristics of direct impact.

同时铜的延伸率、暗地结晶布局等，城市构不败不不对蚀刻液共性的间接感化。

steel . conversion of elongation values . part 2 : austenitic steels.

钢。延伸率的换算。第2 部分：奥氏体钢。

The solution treatment highest is 1 . 155% in the elongation ratio , the aging treatment of metal is higher and the cast condition is lowest .

延伸率是固溶处理以后的最高为 1.155%，其次是时效处理，最低的是铸态条件。

steel . conversion of elongation values . part 1 : carbon and low alloy steels.

钢。延伸率的换算。第1 部分：碳素钢和低合金钢。

The extensibility of alloy treated by antiflux was improved by 30% compared with the untreated alloy.

用高温熔剂处理的合金的延伸率比未经处理的合金提高了 30%。

热词推荐

大家在看

man , . you 's " after cum ? : - Facebook japan what Yeah then your 4th as of