大家在查：卧榻 K-L edulis 许可方 pull through 发行价 the wind 幅肖像溺水身亡 NIC

公称

na.nominal; rated; indicated
网络Nominal Diameter; kN; NOM

公称

英-汉网络释义

公称

nominal

公字的解释---在线新华字典 ... 公车〖 bus〗公称〖 nominal〗公尺〖 metre〗 ...

Nominal Diameter

液化石油气钢瓶-CNG钢瓶... ... 气瓶 Cylinder type No. 公称 Nominal Diameter 工作 Nominal working Pressure ...

indicated

公称支数,nomin... ... ) metric number 公制纱线支数 ) nominal;rated;indicated 公称 ) nominal count;nominal number 公称支数 ...

rated

公称支数,nomin... ... ) metric number 公制纱线支数 ) nominal;rated;indicated 公称 ) nominal count;nominal number 公称支数 ...

kN

产地：江东机械厂主要技术参数:（三）型号公称 (kN) 顶出力（KN）滑块行程(mm) 最大开口距(mm) 工作台尺寸左右×前 (m…

NOM

台湾工程术语与缩写 - 翻译界-翻译论坛 ... 微音器 / 麦克风 MIC 名义 / 公称 NOM 数 / 常开 NO ...

BNC jack

R3131A频... ... 基准电平显示范围对数 -6 4V～+22.36V (公称) BNC jack，10kΩ (自动校正后) (REF=-50dBm～0dBm，ATT=10…

例句：

A grinder may be used to dress the surface defects but its working depth should be no more than 10% of nominal thickness .

冷弯型钢的表面缺陷允许用修磨方法清理，但清理深度不得超过公称厚度的 10%。

"Testing conclusion " indicates the status whether the measured thickness conforms or not to the nominal thickness .

“检验结论 ”填写实测厚度与公称厚度盯符或不相符。

Butterfly valves, sizes 8 "and larger, when used on liquids, show a marked increase in dynamic torque which tends to close the valve . "

对于公称通径大于 8 英寸的蝶阀，如果是在液体中使用，则在关闭阀门时，动态扭矩有比较明显的增加。

Measuring and inspection procedures provide that the established nominal preload force is obtained with the least possible deviation .

测量和检查步骤确保所得到的公称预加载荷力的偏差值尽可能小。

A bilateral tolerance is one where the tolerance range is disposed on both sides of the nominal dimension .

双向公差是在公称尺寸两侧都有公差带的公差。

Pipe size is specified with two non-dimensional numbers : a Nominal Pipe Size (NPS ) and a schedule (SCH ).

管道规格使用两个无纲量的编号来表示：公称管道尺寸规格（NPS ）及抗拉强度（SCH ）。

CLUTCH HOUSINGS FOR RECIPROCATING INTERNAL COMBUSTION ENGINES . NOMINAL DIMENSIONS AND TOLERANCES .

往复式内燃机用离合器箱 .公称尺寸和公差

Nominal size of the pipeline into which the valve will be placed must be determined .

必须确定阀门将要安装进去的管道的公称通径。

Overall nominal dimensions and layout are to be specified.

所有的公称尺寸及平面图

At the concert Presti declared Lagoya the best guitarist she had ever heard .

在音乐会上，普蕾斯蒂公称，拉戈雅是她曾听到过的最好的吉他演奏家。

Be sure to determine the trajectory of docking with the valve nominal diameter .

务必确定与阀门对接的弹道的公称通径。

DN at 50mm below the valve can be used as a pipe socket fittings , pipe thread socket will connect the two parts together .

公称通径在 50mm 以下的阀门可使用管套节作为管接头，管套节的螺纹将连接的两部分连接在一起。

Dental rotary instruments . Nominal diameters and designation code number.

牙科用旋转器械 .公称直径和命名代码

Actual outside diameters in millimetres for pipe are identical to those corresponding to the nominal pipe size (NPS) in inches .

以毫米为单位的管道的实际外径与那些以英寸为单位的相应的公称管道尺寸相同。

Specification For seamless carbon steel pipe For high-temperature service.

高温用无缝碳钢公称管。

It should be considered when choosing the value of nominal cover for design .

在设计中选择保护层公称厚度时，应该考虑这一标准。

D is the pipeline nominal diameter , when the necessity should establish the rectifier unit .

是管道公称直径，必要时应设置整流装置。

PLASTICS-HALF SYMMETRIC FITTING (GUILLEMIN SYSTEM ) WITH LOCKING RING. NOMINAL PRESSURE PN 6.

塑料 .带紧箍的半离合器系统（吉可曼系统）.公称压力 PN6

Nominal pressure solenoid valve should be more than the maximum working pressure tube .

电磁阀公称压力应超过管内最高工作压力。

QUARTER TURN CONNECTIONS (GUILLEMIN SYSTEM ). NOMINAL PRESSURE PN 16 .

对称半边连接管（吉耶曼系统）.公称压力 16

Ball screws . Part 2 : nominal diameters and nominal leads . Metric series.

滚珠螺钉 .第2 部分：公称直径和公称引线 .米制系列

热词推荐

大家在看

man , . you 's " after ? : - Facebook what Yeah then your japan 4th as of own