大家在查： brioche 塌掉母版 LNAGG ICMP display page machine Interface print page 贝多油漆成

收缩率

n.shrinkage ratio
网络Shrinkage; Mold Shrinkage; shrinkage rate

收缩率

英-汉网络释义

收缩率

Shrinkage

模具种类_百度文库 ... flexural strength 抗弯强度 shrinkage 收缩率 regrind usage 次料使用机械设备: ...

Mold Shrinkage

cpvc_百度百科 ... 弯曲强度 Flexural Strength 收缩率% Mold Shrinkage 弯曲弹性模量 Flexural MODulus ...

shrinkage rate

专业英语-注塑成型专业词汇_百度文库 ... oven 烤炉，烘灶 shrinkage rate 收缩率 滞留时间 booster time 增压时间比 ...

shrinkage factor

石油英语词汇(S3)_专业词汇_专业英语_食品伙伴网 ... shrinkage crack 缩裂 shrinkage factor 收缩率 shrinkage fit 烘装热压配合 ...

shrinkage ratio

S ... shrinkage mark 收缩痕 shrinkage ratio 收缩率 shrinkage stoping 留矿法 ...

Shrink Ratio

在“收缩率”(Shrink Ratio) 下，单击下面任一选项，将尺寸插入表中。【同期内容】： ⊙-下一篇：ProE WildFire分模教程之典型 …

contraction percentage

机械词汇的英语翻译(A-G) ... contraction crack 收缩裂缝 contraction percentage 收缩率 contraction rule 缩尺 ...

Molding

台湾化纤PP,K1011,F4008,F2003物性表 ... 比重 Specific Gravity 收缩率 Molding 项目 Property ...

例句：

The shrinkage rate of the injection mould for the various plastics is listed , the calculating applied examples are worked yet.

列出了各种塑料注射模的收缩率，还作了计算应用实例。

the compression ratio and the water-solubility time of the sample also increases directly with the sinter temperature .

随烧结温度的提高，试样的收缩率和水溶时间增大。

Conclusions : The difference in shrinkage of distal margin at different times should be considered in anterior resection for rectal cancer .

结论：直肠癌前切除术肿瘤下切缘的估计应考虑切缘的收缩率。

This paper studies the self-made low profile additive and its influence on shrinkage rate and mechanical properties of UP resin .

本文研究了自制低收缩添加剂用量对不饱和聚酯树脂固化收缩率与力学性能的影响。

However , in practice , use the heat sealing temperature is high, shrinkage .

但在实际应用中，使用的热封温度高，收缩率就大。

The experimental results show that the elongation and area reduction of weld can improved by adding RE oxide in electrode coating material .

结果表明，稀土氧化物能提高熔敷金属的伸长率和断面收缩率；

The results show that, after soaking by acid rain , dry heat shrinkage ratio of the leather increases, and the dry thermostability decreases .

结果表明：经过酸雨浸泡后，加脂皮革的干热收缩率均高于未浸泡试样，耐干热性能下降。

Introducing the example , volume and coverage shrinkage rate of persimmon were calculated .

并通过实例，对柿子干制时的体积收缩率和表面积收缩率进行了计算。

The effects of PET film traverse heat shrinkage rate on loss angle tangent value of capacitor charge -discharge process were introduced .

介绍了聚酯薄膜横向的热收缩率对电容器充放电后损耗角正切值的影响。

The effect of hydrogen of the gear shaft was comparatively evaluated by reduction in area and elongation values in different condition .

用不同条件测得的断面收缩率和延伸率评价了齿轮轴的氢脆效应；

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 : determination of moulding shrinkage.

塑料 .热塑材料试样的注塑法 .第 4 部分：模塑收缩率的测定

The contraction of the skin grafts were measured and compared with other kind of skin grafts.

测量此方法的皮片收缩率，并与其他种类皮片进行比较。

The shrinkage rate and porosity of the compound porous metal were analyzed by SEM and weighting .

分别采用 SEM 观察其几何结构特征和称重法，分析了复合多孔材料的收缩率及孔隙率。

low mold temperature can be reduced mold shrinkage of plastic parts .

低的模具温度可降低塑件的成型收缩率。

At the same time, the hot shrinkage, crimp ratio and crimp rigidity increase with the increasing heat treatment temperature and time .

CDP-FDY 纤维的干热收缩率、卷曲度、卷曲弹性率均随热处理温度的上升、时间的延长而提高。

Setting the packing pressure too high will produce uneven contraction , which results in warp .

在保压压力部分，过高之压力则使工件过于饱和使体积收缩率不均，造成翘曲。

For the sake of the axis accessory's figuration , the experiment of second wedge heavy section shrinkage was carried out.

为了成形大断面收缩率轴类零件，进行了楔横轧二次楔入试验。

热词推荐

大家在看

man , . you 's " after cum ? : - Facebook japan what Yeah then your 4th as of